Heavy Duty Trucking Logo
MenuMENU
SearchSEARCH

Performance-Based Brake Testing

What if you could find out in 10 minutes or less precisely how each and every one of your tractor-trailer's brakes is working? You'd know how much force they're producing to stop the rig, individually and by axle.

Tom Berg
Tom BergFormer Senior Contributing Editor
Read Tom's Posts
May 18, 2009
6 min to read


What if you could find out in 10 minutes or less precisely how each and every one of your tractor-trailer's brakes is working? You'd know how much force they're producing to stop the rig, individually and by axle.
You'd find if threshold air pressures - the point when linings begin contacting the drums - are correct, and if linings are dragging. You'd know the condition of all valves, sensors and wiring, and even if the anti-lock braking system is working correctly. You could quickly examine a computer-generated printout, then send a mechanic straight at any problem.

That's what performance-based brake testing can do, say its proponents, but not many people in North America are listening. PBBT, usually using a wheel dynamometer, originated more than 50 years ago. For at least 15 years it has been used extensively in Europe and elsewhere in the world. About 140,000 brake testers are being used overseas, ranging from 30 in Mongolia to 69,000 in Great Britain. In many countries, vehicle equipment inspections are required twice a year, and each one includes testing of a truck's brakes on such a machine.

In the U.S., fewer than 400 testers are in use, mostly by municipal transit-bus fleets whose vehicles are in really tough service. Other machines are in truck dealers' service departments, and a handful are used by commercial law enforcement officers in a couple of states, according to David Domine, general manager of Link-Radlinski Inc., a brake testing and certification operation at East Liberty, Ohio, that uses and sells brake dynos.

"When they hear that we don't use this technology, they're amazed," he says of his contacts in Europe. Trying to convince truck-fleet managers to use PBBT is difficult, because neither federal nor state laws or regulations require it, and a dyno costs $75,000 to $100,000. Over-the-road fleets whose brakes don't get much wear would have difficulty justifying such an expense, though Domine does have some safety statistics that argue for it. Certain severe-service trucks can benefit, but even their managers don't consider PBBT because "there is great pride among them in believing they're already doing things right" in how they maintain brakes, Domine observes.

Often they aren't.

Brake maintenance in North America is usually done by sight. Someone looks at the condition of drums, linings, slack adjusters and associated parts, and measures the length of push-rod strokes, then adjusts and repairs things as necessary. That's how it goes in most shops. Where drivers complain that brakes just aren't stopping or pull to one side, mechanics look harder for problems and do their best to correct them. If everything looks good and drivers don't complain, the brakes are deemed to be working well, and they might be. At official inspection stations, trucks are passed or put out of service based on visual examinations.

But how exactly is each brake working, and how much force is it applying? Is it doing its share of work, and if not, how much harder are other brakes working to make up for it? Performance-based brake testing shows this by quantifying it, Domine explains.

A comprehensive report generated by a performance-based brake tester shows the amount of braking force (in pounds) divided into the vehicle's gross weight. By federal regulation, the resulting number must be at least 43.3 percent, and it should be somewhat higher, Domine says. Thus the brakes on a rig grossing 78,000 pounds must be able to apply a minimum of 33,774 pounds of force. No visual inspection can determine that except by inference, but the machine can, and it pinpoints the amount of force from the brakes on each axle. That means axle-to-axle balance can be determined and corrected if necessary - the key to effective maintenance.

Further, a PBBT report determines side-to-side balance - how one brake is working with its partner at the other end of the axle. Law enforcement officers are particularly concerned with this, because a serious imbalance can lead to sideward pull and, under hard braking, can yank a truck out of its lane. But, Domine notes, side-to-side numbers on a report can seem alarming when they're not. One brake on an axle can be working 30 percent harder than its mate, but a driver won't notice it, partly because power steering compensates for it, and force being applied on other axles might balance out the errant axle. The side-to-side differential must reach 40 to 50 percent before a driver can feel it, he says.

One believer in the PBBT concept is Dennis McNichol of A.M. Keefe Transport in Broomall, Pa., which hauls building materials and other commodities. McNichol employs a Link-Radlinski dyno in his own brake maintenance program, and uses a portable version in his consulting with transit and refuse fleets. He is active in the Technology and Maintenance Council of the American Trucking Associations, and is among a group that's writing a TMC recommended practice to guide usage of brake dynos. He also sells the Link-Radlinski machines.

"You wanna save money in brakes and you own 25 or 50 trash trucks? Buy one of these machines," he says. "It's all about balance, and these help you do that." He's found that the front brakes on trash trucks are comparatively small and not set to apply hard, so linings polish the drums and become ineffective. Braking work shifts to the rear axles, which are carrying most of the load anyway. Linings on drive axles will wear out three and four times a year while there's little wear on the fronts, and managers think it's normal.

The problem is acute in transit buses, he says. Overheated rear brakes in a fleet in Miami, Fla., set two buses afire, and it took dyno testing to show managers that front brakes had to be put to work. Even after pinpointing the underlying problem, it took major attention to workmanship by mechanics to get braking systems operating correctly.

"I went to one of the major trash fleets and found the same thing - the front axle (brakes) not doing any of the work, the back axles were doing all the work," McNichol says. "If you see the performance is wrong (on the dyno), you can go back to the manufacturer and see what can be done to bring performance back to OE specs. Otherwise, replace the linings with something that's gonna do the job."

Multi-axle combinations like Michigan trains and dump trucks with several lift axles are also good candidates for performance-based brake testing, especially if they operate locally with a lot of stops and starts, Domine says. That's because the many brakes on these vehicles are difficult for a short-handed shop crew to watch and keep in adjustment, much less in proper balance. A PBBT machine can spot problems quickly and prompt quick and efficient repairs.

McNichol gives an example he's seen: "A driver writes 'bad brakes!' on an equipment report and that's all. So the mechanic takes the truck for a test drive and sees that it pulls to the right when he applies the brakes. He runs a brake test on the machine and finds one front brake that's really aggressive, so he takes off that wheel. This tractor is equipped with an automatic greasing system, and he finds that the line leading to the kingpin near that wheel is leaking grease onto the brake lining. He fixes the line, cleans up the lining and that's it. Without the machine, he'd have to make a seat-of-the-pants decision. He might take off both wheels instead of one. So the machine helps him focus the repair," and that saves time and money.

Through effective maintenance, a trash fleet of 60 trucks could save enough in brake wear to pay off a $100,000 tester in about two years, Domine figures. This is a portable, above-ground model; an in-ground version costs $75,000 to $85,000, and installation costs are minimal if it's part of the construction of a new shop or inspection building to house the machine.

Fleets not wanting to spend such money might get Dom

Subscribe to Our Newsletter

More Maintenance

Maintenance•by Staff•November 16, 2026

Daimler, Paccar Recall Trucks Over Driveline Defect

Nearly 4,900 Freightliner, Western Star, and Kenworth trucks are being recalled because a missing snap ring could allow the driveline to separate from the truck.

Read More →
Maintenance technician holding tablet in shop environment with truck in background
Maintenance•November 16, 2026

What to Look for in Fleet Maintenance Software

Choosing the right maintenance technology starts with identifying the problems you need to solve. Here's what trucking fleets should look for — and what to ask potential providers.

Read More →
Bendix iTABS X trailer antilock braking system module shown in the foreground, with a tractor-trailer traveling on a highway in the background.
Equipment•by News/Media Release•November 11, 2026

Bendix Upgrades Trailer ABS With Smarter Diagnostics

The new iTABS X system replaces Bendix's TABS-6 Standard trailer ABS, adding faster diagnostics and connectivity that could help fleets identify brake-system problems before they lead to downtime.

Read More →
Ad Loading...
 Commercial vehicle inspector looking closely at truck engine
Safety & Compliance•by Staff•November 11, 2026

CVSA Sets 2027 International Roadcheck Dates

The annual 72-hour truck inspection blitz will take place May 11–13 across North America. Here's what fleets can expect and what inspectors found during the 2026 event.

Read More →
Fleet Management•by Staff•November 10, 2026

What Trucking Events are Happening in 2027?

Looking for trucking-related conventions, expos, and other events? Heavy Duty Trucking has developed this list of national and larger regional trucking shows and events.

Read More →
CVSA inspector looking at brakes underneath truck
Maintenance•by Staff•November 9, 2026

Brake Problems Sideline 15% of Inspected Trucks

During CVSA's 2026 Brake Safety Week, inspectors placed nearly 2,400 commercial vehicles out of service for brake violations, including problems with defective brakes, hoses, drums and rotors.

Read More →
Ad Loading...
A row of black bottles with red, yellow, blue, and green labels
Sponsored•November 6, 2026

Unlocking the performance advantages of PC-12

2027 will mark the arrival of a new generation of heavy-duty engine oils. PC-12 reflects how far engine design has advanced and the demands that progress places on heavy-duty lubricants. Here’s what the transition means to your fleet.

Read More →
A man working on a truck engine, holding a wrench
Sponsored•November 3, 2026

6 Tips for Troubleshooting Cold-Weather Truck Problem: Don't Guess, Diagnose it

Cold weather can expose hidden truck problems. Discover six practical troubleshooting tips to pinpoint the cause, avoid unnecessary repairs and keep trucks on the road.

Read More →
A GP Transco tractor-trailer crosses a bridge over a river, with trailer side skirts visible beneath the white trailer.
Fuel Smarts•by Deborah Lockridge•October 27, 2026

How GP Transco Builds Fuel Savings a Fraction at a Time

Aerodynamic specs, solar panels, and driver incentives help GP Transco turn small efficiency gains into savings it can reinvest in its people.

Read More →
Ad Loading...
Maintenance•by Deborah Lockridge•October 23, 2026

Oil Crisis Squeezes Trucking Lubricant Supplies

Fleets report higher lubricant costs as Middle East disruptions tighten supplies of ingredients used in synthetic engine oils and some driveline lubricants.

Read More →