Heavy Duty Trucking Logo
MenuMENU
SearchSEARCH

Time to Grease, Inspect Fifth Wheels, SAF Holland Advises

Winter temps can freeze all kinds of mechanical apparatus, including tractor fifth wheels. So it’s a good time to clean, inspect and grease these important appliances, but not the only time.

by TruckingInfo staff
December 11, 2013
Time to Grease, Inspect Fifth Wheels, SAF Holland Advises

Important seasonal PM for a Holland FW35 fifth wheel.

2 min to read


Winter temps can freeze all kinds of mechanical apparatus, including tractor fifth wheels. So it’s a good time to clean, inspect and grease these important appliances, but not the only time, according to SAF Holland, one of the principal manufacturers.  

Ad Loading...

Its experts advise the following steps: 

Ad Loading...
  • Lubricate the locking mechanism every three months or 30,000 miles. Do this by removing old grease and debris from all fifth wheel-to-trailer contact surfaces, then apply new water-resistant lithium-based grease to all fifth wheel-to-trailer contact surfaces. There are differences in lubrication needs and intervals depending on whether you have a standard, greased fifth wheel or a no-lube version. 

  • Thoroughly clean moving components in the locking mechanism every six months or 60,000 miles, using a spray product like WD-40 or CRC. Also do this every spring for fifth wheels operating in snowy or icy winter conditions. Lubricate the fifth wheel locking mechanism according to instructions in the manufacturer’s user’s manual. 

  • Inspect for bent, broken or missing parts every 6 months or 60,000 miles. Replace as necessary, and use only your manufacturer’s parts. 

  • Check the operation by locking and unlocking using a lock tester. Verify that the fifth wheel is completely closed, per instructions in the user’s manual. 

This work might also be necessary if problems with coupling, uncoupling or pulling the release handle occur.  

Aside from periodic servicing, maintain lubrication on fifth wheel-to-trailer contact surfaces, using water-resistant lithium-based grease. Clean grease grooves if a large amount of debris is present.

Remember that low-lube and no-lube fifth wheels do not require lubrication between the trailer and top plate surface. 

If the fifth wheel has an air release or is a sliding type, follow the user’s manual for inspecting and lubricating the air cylinder or slide base. 

Ad Loading...

A final and sobering recommendation: Failure to properly install, operate, or maintain your fifth wheel could result in tractor and trailer separation causing death or serious injury to others.

Important seasonal PM for a Holland FW35 fifth wheel.
Subscribe to Our Newsletter

More Maintenance

Collage of Top 20 Product award ceremonies
EquipmentMarch 31, 2026

HDT Honors the Best New Products of 2025 at TMC

Heavy Duty Trucking's Top 20 Products awards recognize the best new products and technologies. Check out the award presentations at the 2026 Technology & Maintenance Council annual meeting.

Read More →
freightliner whitepaper
SponsoredMarch 31, 2026

Detroit Engines: Trusted Performance, Built for What's Next

The Detroit® Gen 6 engine platform proves that real progress doesn’t require a complete redesign. Built on 20 years of trusted technology, these engines are designed for efficiency, stronger performance, and greater reliability than before. And they do it all while complying with 2027 EPA standards on every mile.

Read More →
Illustration showing diesel exhaust fluid pump sign and EPA headquarters
Equipmentby Deborah LockridgeMarch 30, 2026

EPA Targets DEF Sensor Failures Behind Truck Derates

New guidance allows engine makers to replace problematic DEF sensors with NOx-based systems, aiming to reduce unnecessary derates and downtime caused by failures in the sensors designed to monitor diesel exhaust fluid on trucks.

Read More →
Ad Loading...
Goodyear steer tire on display at booth
Maintenanceby Deborah LockridgeMarch 25, 2026

Goodyear Targets ‘Super-Regional’ Sweet Spot with New Steer Tire

Goodyear is preparing to roll out a new steer tire designed to bridge the gap between regional and linehaul for trucking fleets.

Read More →
Hendrickson TireMaax Pro Watchman
Maintenanceby Jack RobertsMarch 25, 2026

Hendrickson Unveils Watchman Smart Wheel-End System at TMC

Hendrickson’s new sensor platform integrates with its TireMaax system to deliver real-time tire and wheel-end insights, targeting uptime and cost savings.

Read More →
Volvo VNL.
Maintenanceby Jack RobertsMarch 24, 2026

Over-the-Air Updates and the Modern Powertrain Explained

Over-the-air updates are moving beyond recalls, and expanding how fleets manage performance, compliance, and uptime.

Read More →
Ad Loading...
SKF TraX wheel monitoring system.
Maintenanceby Jack RobertsMarch 24, 2026

SKF, TMC Expand Hands-On Training to Boost Technician Skills at Annual Meeting

A new partnership between SFK and TMC brings certified, on-site instruction focused on wheel-end reliability and maintenance best practices.

Read More →
Graphic illustrating recruiting concept
Maintenanceby Deborah LockridgeMarch 23, 2026

Why Higher Pay Isn’t Fixing the Heavy-Duty Technician Shortage

Hiring heavy-duty truck technicians has become a bidding war, but shops that focus on culture, training, and career paths are gaining an edge. That's the takeaway from a TMC panel discussion.

Read More →
Tesla Semi electric truck
EquipmentMarch 23, 2026

Technology & Maintenance Council 2026 Annual Meeting [Photos]

Couldn't make it to Nashville for TMC's 2026 annual meeting? Check out these images.

Read More →
Ad Loading...
Bar graph illustrating survey responses on current and future use of artificial intelligence in heavy duty repair shops
Maintenanceby Deborah LockridgeMarch 19, 2026

Fullbay Report: Heavy-Duty Shop Revenue Up, Rates Rising, but Shops Still Short on Techs

Strong growth across the heavy-duty repair sector is being tempered by workforce shortages and an aging technician pipeline.

Read More →