NTSB Says Design Flaw Caused I-35W Bridge Collapse
The collapse of the I-35W bridge in Minneapolis was caused a design flaw that led to the bridge not being able to take the weight of concentrated construction loads on the bridge, exacerbated by inadequate inspection procedures
The collapse of the I-35W bridge in Minneapolis was caused a design flaw that led to the bridge not being able to take the weight of concentrated construction loads on the bridge, exacerbated by inadequate inspection procedures.
The National Transportation Safety Board announced its findings late last week. It said the design error led to inadequate load capacity of the gusset plates at the U10 nodes, which failed under a combination of (1) substantial increases in the weight of the bridge, which resulted from previous modifications, and (2) the traffic and concentrated construction loads on the bridge on the day of the accident. The NTSB had previously reported that an estimated 99 tons of sand were putting stress on the bridge when it collapsed in August 2007.
Also contributing to the collapse, the NTSB said, was the generally accepted practice among federal and state transportation officials of giving inadequate attention to gusset plates during inspections for conditions of distortion, such as bowing, and of excluding gusset plates in load rating analysis.
"We believe this thorough investigation should put to rest any speculation as to the root cause of this terrible accident and provide a roadmap for improvements to prevent future tragedies," said NTSB Acting Chairman Mark V. Rosenker. "We came to this conclusion only through exhaustive efforts to eliminate each potential area that might have caused or contributed to this accident.
"Bridge designers, builders, owners, and inspectors will never look at gusset plates quite the same again, and as a result, these critical connections in a bridge will receive the attention they deserve in the design process, in future inspections, and when bridge load rating analyses are performed."
About 6:05 p.m. Central Daylight Time on Wednesday, August 1, 2007, the eight-lane, 1,907-foot-long I-35W highway bridge over the Mississippi River in Minneapolis experienced a catastrophic failure in the main span of the deck truss. As a result, 1,000 feet of the deck truss collapsed, with about 456 feet of the main span falling 108 feet into the 15-foot-deep river. A total of 111 vehicles were on the portion of the bridge that collapsed. Of these, 17 were recovered from the water. As a result of the bridge collapse, 13 people died, and 145 people were injured.
During its investigation, the Safety Board learned that 24 under-designed gusset plates, which were about half the thickness of properly sized gusset plates, escaped discovery in the original review process and were incorporated into the design and construction of the bridge.
The NTSB examined other possible collapse scenarios - such as corrosion damage found on the gusset plates at the L11 nodes and elsewhere, fracture of a floor truss, pre-existing cracking in the bridge deck truss or approach spans, temperature effects and shifting of the piers - and found that none of these played a role in the accident.
As a result of its investigation, the NTSB made nine recommendations to the Federal Highway Administration and the American Association of State Highway and Transportation Officials dealing with improving bridge design review procedures, bridge inspection procedures, bridge inspection, training and load rating evaluations.
A synopsis of the Board's report, including the probable cause, conclusions, and recommendations, is available on the NTSB's website, www.ntsb.gov, under "Board Meetings." The Board's full report will be available on the website in several weeks.
More Drivers

Catching Driver Fatigue is One Thing. What You Do Next Matters Just as Much
Fleets are getting better at detecting driver drowsiness. Few have figured out what should happen next, and that gap is where the real risk still lives.
Read More →
133 ELDs Revoked as ATA Pushes Certification Reform
FMCSA just removed a record number of electronic logging devices from its registry. ATA says it's time to rethink how ELDs get approved in the first place.
Read More →
CVSA Sets 2027 International Roadcheck Dates
The annual 72-hour truck inspection blitz will take place May 11–13 across North America. Here's what fleets can expect and what inspectors found during the 2026 event.
Read More →
FDA Eases Path for Oral-Fluid Testing
Federal actions could advance oral-fluid drug testing for truck drivers, but lab certification delays and marijuana rescheduling questions remain.
Read More →
Why Hiring Truck Drivers Is Getting Harder
Higher recruiting costs, a shrinking driver pool, and renewed pay competition are raising the stakes for fleets heading into 2027.
Read More →
Roehl Offers Truck Drivers $10,000 Retention Incentive
Payments begin after the first load and continue in mileage-based installments for eligible experienced drivers joining the fleet.
Read More →
Platform Science Adds Dispatch and Safety Tools
Four additions to PS Fleet help fleets monitor loads, manage driver coaching, share truck locations and adjust video system settings.
Read More →
When Language Stops the Truck: The Return of ELP Out-of-Service Orders
English language proficiency rules for commercial drivers aren’t new, but renewed out-of-service enforcement has raised the stakes. Here’s what carriers need to know before a driver reaches a roadside inspection.
Read More →
Samsara Launches Custom AI Agent Builder
Agent Studio lets fleets create AI tools for hours-of-service monitoring, reporting and driver support, including agents that communicate by phone.
Read More →
Trucker Path Expands Reserved Parking Network
Trucker Path has added close to 6,000 more truck parking spaces to its Trucker Path Reserved Parking Network with the addition of Safe Truck Parking.
Read More →

