Private Fleets Back Higher Truck Weight Limit
The National Private Truck Council is now throwing its own weight behind the legislative effort to allow individual states to increase the federal vehicle weight limit to 91,000 pounds for tractor-trailers that are equipped with a sixth axle.

A House bill would let states set a 91,000-pound weight limit on highway rigs fitted with a sixth axle, similar to this truck built for operation in Maine.

The National Private Truck Council is now throwing its own weight behind the legislative effort to allow individual states to increase the federal vehicle weight limit to 91,000 pounds for tractor-trailers that are equipped with a sixth axle.
Although NPTC is a member of the most active lobby for upping the federal GCW limit, the Coalition for Transportation Productivity, the association that represents some 600 private fleets said on October 9 that it has directly voiced its support for truck-weight reform in a letter sent to the members of the House Transportation and Infrastructure Committee.
That committee is charged with drawing up the House version of the long-overdue highway bill, which NPTC wants to see incorporate the Safe, Flexible and Efficient (SAFE) Trucking Act (H.R. 3488) introduced in September by Rep. Reid Ribble (R-WI).
NPTC contends that Ribble’s measure would give states the “flexibility to safely confront highway capacity issues” by letting carriers run heavier, six-axle trucks on Interstate highways within their borders.
“H.R. 3488 would improve options for enhancing productivity,” wrote Gary Petty, president and CEO of NPTC. He stressed that the association “would not support this legislation if our members thought that it might diminish safety or harm highway or bridge infrastructure.”
Petty also called out the railroad lobby's effort to derail Ribble’s proposal. “We understand that the railroad industry and their surrogates are opposed to this bill,” he wrote. “But railroad interests should not hold a veto over highway transportation policy. They should compete for freight in a free and fair marketplace that allows for productivity enhancements for all modes.”
He also made the point that H.R. 3488 “does not mandate anything. It would merely allow the state governments to permit truck combinations up to 91,000 pounds in a six-axle configuration to use the Interstate highways in their state. State agencies would retain the ability to limit or even prohibit use of these vehicles when safety dictates otherwise. Moreover, use of six-axle vehicles at 91,000 lbs. would not create additional harm for pavement or bridges.”
The NPTC letter is the latest word from a trucking-affiliated group that has publicly stated that it is either for, against, or (for lack of a better word) neutral on Ribble’s SAFE Act.
In a Sept. 16 letter sent to Ribble, the Truckload Carriers Association argued strongly against allowing the increase in the weight limit. Recognizing that the bill “attempts to improve trucking productivity on our highways,” TCA stated that it opposes the measure because “it clearly would only benefit a minority of the industry.”
The truckload group also contended that the cost to properly equip trailers and tractors to take advantage of the higher weight limit would not be compensated by rate increases, yet carriers would be compelled by customers to invest in the more costly equipment.
Like TCA, The Trucking Alliance, a coalition of trucking businesses that lobbies for safety improvements, does not support the bill. “This legislation wasn't written to benefit trucking companies, because it would drive up operating costs, drive down truck driver wages and curtail investments in safety technologies,” Lane Kidd, the Alliance’s Managing Director, told HDT.
When asked by HDT if the American Trucking Associations had any reaction to the bill, ATA spokesperson Sean McNally replied, “No, we don’t.”
More Equipment

Michelin Expands X Line Grip D Tire Line
Michelin is expanding its X Line Grip D drive tire lineup with a new pre-mold retread and additional sizes, building on what the company says is strong fleet adoption of the tire's traction, mileage, and fuel-efficiency benefits.
Read More →
Engine Technology Forum Launches SCR, DEF Resource Center Amid Emissions Debate
The Engine Technology Forum’s new online hub aims to provide fleets, policymakers, and equipment owners with fact-based information about selective catalytic reduction technology, diesel exhaust fluid and emissions compliance.
Read More →
Prime Inc. to Open $7.9M Flagship Used-Truck Dealership
A new driver-focused facility to sell Prime Inc's used trucks and trailers will be the first purpose-built location in the company's history.
Read More →
Lessons Learned About Alternative Fuels: Start Small, Stay Flexible
Practical advice on adopting alternative fuels and ZEVs from HDT's 2026 Top Green Fleets, from renewable diesel and natural gas to electric trucks.
Read More →
Kenworth Names Peter Ahrens General Manager
Leadership changes at Kenworth take effect July 1 as the OEM promotes two longtime Paccar executives to key management roles.
Read More →
Hino Adds Electric Class 6/7 Truck
Hino says the Le Series is an important step in the company's efforts to reduce environmental impact and support its customers’ sustainability goals.
Read More →
ACT Expo 2026: Highlights in Photos
The 2026 Advanced Clean Transportation Expo featured a broad range of commercial vehicle technologies, from EVs to autonomous trucks to the latest diesel and alternative-fuel engines.
Read More →
Hendrickson Debuts Electraax E-Axle for Medium-Duty Trucks
Developed with Driventic, Hendrickson's new integrated e-axle is designed to improve efficiency, reduce weight, and extend range in Class 6-7 EV applications.
Read More →
Peterbilt Unveils Freedom 250 Special Edition Model 589
Peterbilt’s just-announced limited-run patriotic Model 579 tractor celebrates America’s 250th birthday with custom styling and premium features.
Read More →
Mack Unveils EPA 2027-Compliant MP13 Engine With More Power, Better Fuel Economy
Along with unveiling its EPA 2027-compliant MP13 engine, Mack outlined powertrain changes across its Class 6-8 lineup, including new Cummins-based X10 engines.
Read More →
