Equipment

7 Factors to Consider When Installing an Inverter

From what size to get to company policies, what fleets need to know when choosing and installing a power inverter.

September 2013, TruckingInfo.com - WebXclusive

by Truckinginfo Staff

SHARING TOOLS        | Print Subscribe

 

3. Installation: Can fleets install an inverter?

“Generally speaking, yes,” says Carlson.  “Most technicians will have no problem handling installation, and Xantrex does offer fleet training programs to our customers. We certainly would recommend our training program if there are any questions on installation.

“But, just remember, you’re working with electricity and electricity can bite if you’re not careful.  It’s our recommendation that inverters over 300 watts feature hard-wiring and fusing.”

ADVERTISEMENT

Carlson says there is a bevy of things to consider when installing an inverter, starting with ‘where it should go’ and making sure there is adequate ventilation to allow heat to dissipate.

“And you have to be cognizant of wire sizing and the distance between the inverter and plug-ins which can be put in the sleeper; plus the distance between the battery and inverter. There’s a lot to consider.”

According to Carlson, most fleets want the convenience of a factory-installed and warranted inverter. 

“We really recommend either an OEM install when you purchase a new truck, or have the installation done by an authorized dealer,” says Carlson. “The OEMs have installation down to a science and it’s done on the line to rigid specs. Truck and aftermarket dealers also have the experience, so it’s worth spending a few extra bucks to have the installation done right, the first time, should your own staff not have the time or expertise.”

4. Reliability

“When it comes to reliability, the old adage, ‘you get what you pay for’ comes into play,” says Carlson.

You will pay more for an inverter that has a ‘Regulatory Listed’ approval – such as UL or ETL with UL458 rating. This means the inverter was inspected and approved by an independent agency which safeguards against issues with electricity. UL458 is the listing for inverters and chargers in mobile applications. They must meet strict vibration, environmental, and thermal requirements that non-UL458 units do not.

"This is the most important safety point I can make, and in fact, TMC's RP163 calls out this UL listing for all inverters and chargers installed in a truck," Carlson says.

The RP160 that discusses DC and AC wiring in a truck has requirements that are automatically met by UL458 listed inverters. The main point being that the neutral and ground are bonded together within the inverter.

"All inverters that are not UL458 listed do not do this, he says, as it allows the inverter to be made at a much lower cost."

Buying an inverter that is not Regulatory Listed tells you ‘buyer beware.’ “We’ve seen these types of products actually shock users, plus internally they often can’t protect themselves against power surges.”

Carlson says inverters installed by truck manufacturers all are UL approved, but most inverters sold at truckstops are not.

Carlson also suggests you look for how inverters are internally tested for quality control.

“If the manufacturer you’re considering tests to ensure quality, then they’ll likely promote that fact in their marketing material, or on their web site,” he says. “And, those inverters that have been tested will last longer versus inverters from manufacturers that don’t spend the time and money to ensure quality. A quality inverter should last well beyond its warranty period.”

Carlson says inverters will occasionally shut down, but quality inverters do so without damaging themselves.

“If dust or cat hair, for instance, gets inside the inverter, it can cause it to overheat. A higher watt Xantrex inverter, for example, has an error code that lets you know what the problem is – in this case it will tell you that you are overheating and to check the fan.  A simple cleaning or ‘blowing out’ will correct the problem and you’ll be back up and running.  Other inverters could leave you guessing as to what the problem is.

“And, if you overload the inverter, placing more wattage demands on the inverter than it can handle, the inverter will shut down.  The difference between a quality inverter and low-end inverter is how they deal with a shut down. A quality inverter is designed to shut down with no ill effects. A low-end inverter can ‘wear out’ after multiple overloads.”

5. What about a built-in battery charger?

“The simple answer is yes if you can use ‘shore power’ (electrical outlets at home or on the road at terminals, loading docks, or truckstop),” says Carlson. “When plugged in, you can run everything you’re running with your inverter for as long as you want, plus you can recharge and top off your batteries. The more you can use shore power, the better, as it prolongs the life of your batteries.”

In fact, Carlson says having the shore power option and a charger in the system will add 20% to 30% to the life of the batteries if plugged into grid power whenever possible. “It also has the potential to eliminate one battery swap out over the five to six years use of the truck. This happens by keeping batteries fully charged, offsetting parasitic loads, and reducing the number of cycles.”

According to Carlson, most installations use the inverter off the truck’s starting batteries and quality inverters will have a low voltage disconnect (LVD) to shut down when voltage drops to 11.7 volts. This ensures the truck will have enough juice to start. 

“Check on the LVD feature before you buy an inverter,” cautions Carlson. “Many inverters on the market will run the batteries down to 10.5 volts, which will let drivers run electrical devices longer in the cab and sleeper.  However, they won’t be able to start the truck unless the truck comes equipped with its own LVD.

“Another option is to run two dedicated deep-cycle batteries and connect them to the inverter,” continues Carlson. “Yes, they do add weight to the vehicle, and added cost. But, deep-cycle batteries were designed to be drawn down to a 50% state of charge, or 10.5 volts. This gives you double to triple the amount of continuous power to run hotel loads.  Something your drivers will appreciate.”

6. Policies about bring-your-own inverters

According to Carlson, not knowing what kind of inverter your driver is bringing in is why fleets often have a policy of not allowing drivers to outfit company trucks with their own inverters. 

“If you do allow drivers to bring in their own inverters, then we recommend you give them a list of approved devices, with the most important common denominator being UL458 listed. And we suggest you make it mandatory that your shop or outside dealer does the installation.”

7. Inverters and APUs 

The addition of an inverter to a truck electrical system will reduce hours of use on a diesel-fired auxiliary power unit (assuming that the APU does not already have shore power compatibility). “And, it will reduce maintenance costs and increase APU life,” said Carlson. “An inverter can be used for hotel loads in the cab as long as environmental conditions do not require air conditioning. When those conditions happen, just power up the APU for air conditioning.” 

With this set-up, the only time the APU would need to come on is if the batteries drop to a low level. Once the batteries are charged, the APU can shut off again. “This significant reduction in APU run time means a quick payback on the cost of the inverter,” says Carlson.


« Previous  |  1  2  |  Next »

Comments

  1. 1. Eric C [ September 05, 2013 @ 02:36PM ]

    Try AIMS Power inverters ... http://www.aimscorp.net

  2. 2. deco [ September 09, 2013 @ 01:33AM ]

    Inverters on the market, there are two types, a sine wave and modified sine wave.

    "Two work well in a truck environment, but for those with sensitive electronic equipment (eg CPAP machine) or product, drill or insert your own toothbrush charger - sine wave is the preferred

    http://www.gridtiepowerinverteronline.com/

 

Comment On This Story

Name:  
Email:  
Comment: (Maximum 2000 characters)  
Leave this field empty:
* Please note that every comment is moderated.

Newsletter

We offer e-newsletters that deliver targeted news and information for the entire fleet industry.



GotQuestions?

LUBRICANTS

The expert, Mark Betner from Citgo will answer your questions
Ask a question

Sponsored by

Magazine