What do you know about the synthetic web strapping you use to secure cargo? What you need to know is that it has a label, tag or stencil showing the manufacturer's name and/or trademark, and the working load limit of the strap in pounds or kilograms. You've got all that? The label even says the strap is DOT approved. You're good to go, right?

Guess what? There are no DOT standards for cargo strapping.
Testing demonstrated that even minor cuts in the sides of the tested straps caused failures at much lower tension than expected.
Testing demonstrated that even minor cuts in the sides of the tested straps caused failures at much lower tension than expected.


The FMCSA's cargo securement rules incorporate by reference manufacturing standards for certain types of tiedowns -- including synthetic webbing -- developed by the Web Sling & Tie Down Association. That group describes its own manufacturing standard as more of a guide than a requirement. The following caveat appears on page two of the Web Sling & Tiedown Association's Recommended Standard Specification for Synthetic Web Tiedowns:

This recommended standard specification has been formulated as a guide to users, industry and government to ensure proper use, maintenance and inspections of synthetic web tie down assemblies. The existence of this recommended standard specification does not, however, prevent members of the Web, Sling, & Tie Down Association, Inc. and other manufacturers from manufacturing or selling products not conforming to this standard.

"It's ironic; you can't buy a $10 lamp in this country that doesn't have an Underwriter's Laboratory (UL) approval sticker on it, but there's no policing of the cargo securement product sold to the trucking industry," says Ralph Abato, vice president of sales and marketing for Ancra International.

Abato has raised the issue of cargo strap quality with enforcement officials, and he has provided test data showing some of the commercially available product falls alarming short of its indicated working strength.

"The biggest issue is the influx of importers and local sellers of strap assemblies that don't meet any standards at all," Abato says. "They either don't understand the standards or don't care. They don't do any testing, and they put out vastly inferior product that's basically mislabeled."
On top of that, when it comes to enforcing the cargo securement rules, inspectors tend to take the rating labels and tags at face value, he says. "They're looking for compliance with the total number and working load limit (WLL) of the tie down devices. They rarely question the integrity of the straps' rating."

Strap condition

In 2009, Abato brought some documented cargo strap testing to officials' attention that shows, among things, that straps might be more prone to abrasion and crushing damage that originally thought. The testing also demonstrated that even minor cuts in the sides of the tested straps caused failures at much lower tension than expected.

Ten samples of new, commercially available 4-in. cargo strapping rated at 20,000 pound breaking strength were intentionally damaged (minor damage) in repeatable ways and then subject to a destructive pull test. The undamaged samples all exceeded the rated breaking strength in a preliminary test.

With an edge cut of 10 percent of the width of the strap (about a quarter of an inch), the average breaking strength was 47.4 percent of the new breaking strength. Actual breaking tension ranged from 9,368 pounds to 9,480 pounds out of 20,000.

Simulated abrasion testing revealed the test straps failed at 69.5 percent of the rated breaking strength. The straps all ruptured at the point the strap had been damaged.

In a combination test, with simulated abrasion and a 10-percent edge cut, the straps survived only 15 alternating cycles of a full working load limit pull test, failing at an average of 29.6 percent of the 20,000-pound breaking strength, or just 5,924 pounds.

Abato says he has not yet heard from CVSA on how it might proceed, armed with this information, but he expects there will be another round of testing done to verify the previous tests.

It's certainly cause for concern, but not panic. CVSA is looking at the issue of edge damage to cargo straps, and is contemplating a tightening of the standards. The key take away-here is to use quality strapping from a reputable manufacturer, make sure it's properly marked, and keep in it good condition.

Read more about cargo securement in the June issue of HDT.

About the author
Jim Park

Jim Park

Equipment Editor

A truck driver and owner-operator for 20 years before becoming a trucking journalist, Jim Park maintains his commercial driver’s license and brings a real-world perspective to Test Drives, as well as to features about equipment spec’ing and trends, maintenance and drivers. His On the Spot videos bring a new dimension to his trucking reporting. And he's the primary host of the HDT Talks Trucking videocast/podcast.

View Bio
0 Comments