Maintenance

Getting Your Cooling System Ready for Winter

Winter is coming. Is your cooling system ready for the icy blasts?

October 2015, TruckingInfo.com - Feature

by Jim Park, Equipment Editor - Also by this author

SHARING TOOLS        | Print Subscribe
Photos: Jim Park
Photos: Jim Park

You can almost hear the cooling systems of the nation heaving a sigh of relief as the hot summer weather abates in most parts of the country. But don’t kid yourself – winter isn’t any easier on the cooling system. As temperatures dip and the leaves change from green to yellow and red, it’s time to think about winterizing your trucks for the siege ahead.

As a resource for cooling system maintenance, the American Trucking Associations’ Technology and Maintenance Council offers Recommended Practice 313 C. You won’t go wrong following these guidelines. 

Of primary importance this time of the year is the coolant mixture. You need adequate freeze protection, especially in the north where ambient temperatures of 10 or 20 below zero are common for several months. If the trucks stay in the South, you can get away with a leaner mixture, but you have to consider the likelihood of them straying north. The standard recommendation is a 40%-60% coolant-to-water blend, which will provide freeze protection down to minus 10 to minus 60 degrees.

TMC’s RP 313C cautions that any blend of 60% coolant or more could result in the fluid thickening at really low temperatures and reducing cooling system performance. A 50/50 mix will protect the system from freezing down to 34 degrees below zero.

That RP recommends using an optical refractometer to check the coolant/water ratio rather than a hydrometer because of its accuracy, speed and simplicity.

That’s the easy part. Sorting out which type of coolant the truck is using could be tricky, and have more serious implications if you get it wrong. It used to be easy when all we had was the traditional low-silicate coolants, says Peter Woyciesjes, worldwide RD&E manager, coolants, for Prestone Products Corp.

“Today we have several types of coolant in common use in heavy-duty diesel engines,” he says. “They are commonly differentiated by color, but that’s not always a reliable guide. There are companies that differentiate their product types by color. Unfortunately there are some manufacturers that will use three different colors for the same fluid or technology. That can create problems.”

Getting the wrong coolant

Check when adding top-off fluid that it’s compatible with what’s in the engine. Color isn’t always a reliable guide. 
Check when adding top-off fluid that it’s compatible with what’s in the engine. Color isn’t always a reliable guide.

Woyciesjes says mixing two different types of coolant should be avoided, but notes that a mix isn’t the end of the world.

“If you inadvertently mix red organic acid coolant and green conventional coolants, you won’t have any problems in terms of the key parameters – specifically its heat transfer properties,” he says. “The product will still cool the engine and you’ll have your freeze and boil-over protection. However, you’re now starting to mix chemistries, and you won’t get optimum performance from the coolant.”

TMC and most of the coolant manufacturers say a mix of up to 15% of a different type of coolant won’t cause any difficulties. If you have more than that, you should consider flushing the system and restoring the coolant that you want in the engine.

Maintenance staff should communicate with drivers the importance of preventing mixes, and urge them to report on-road top-offs so they can be alerted to a possible mix.

“Blends can happen when there a leak in the system and the driver is constantly adding make-up coolant of perhaps the wrong type,” cautions Woyciesjes. “It never hurts to monitor the coolant chemistry at PM time or any time after repairing a leaking cooling system.”

Homer Hogg, manager of technical development at TA Petro Stopping Centers, says some of coolants are compatible with each other, but not all.

Physically check the clamps for tightness and make sure the fan shroud is properly attached to the radiator and aligned with the fan. 
Physically check the clamps for tightness and make sure the fan shroud is properly attached to the radiator and aligned with the fan.

“Metals protection is really the issue today,” Hogg explains. “These coolants are formulated with additive packages to prevent cavitation corrosion on wet-sleeve cylinder liners. Different OEMs take different approaches to this and so their coolant formula recommendations can be different.”

Hogg cites Detroit Diesel as one OE that is moving away from extended-life nitrite coolants.

“They have traditionally used the red extended-life coolants, but they have decided to move to a non-nitrite extended life formulation,” Hogg says.

The switch has a lot to do with the introduction of aluminum radiators into the heavy-duty fleet.

“Those radiators are assembled with a process called controlled atmosphere brazing, and some of the coolants on the market will react with the surface the weld and not perform as well,” Woyciesjes explains. “The non-nitrited fluids are more compatible with the newer radiator designs.”

The choice of which coolant to use was probably decided by the manufacturers of the truck you’re working on, but in mixed fleets or those using newer engines alongside legacy engines, coolant maintenance requires a little extra vigilance.

System inspection

Belts should be checked with a proper gauge, as today’s newer belts don’t show the same wear characteristics as yesterday’s belts. 
Belts should be checked with a proper gauge, as today’s newer belts don’t show the same wear characteristics as yesterday’s belts.

With the high heat load on today’s engine, even in cold weather, the need to maintain the cooling system has never been more pressing. That means the entire system needs a trained eye cast over it a couple of times a year. Things like fan shrouds can work loose over time, compromising air flow through the radiator core and possibly jeopardizing the fan blades in a worst-case scenario.

And of course the belts are critical to proper operation of the cooling system and a few other components.

“The types of belts in use today are much different from the old neoprene belts and their wear patterns and indicators are different,” notes Hogg. “You won’t see the cracking we used to see. Consequently, it’s much harder to tell a belt’s condition just by looking at it.”

Hogg says you need to use a belt gauge to measure the depth in the peaks and valleys of the belt.

“There’s some training required to use a belt gauge properly, so it really does require a properly trained technician using the proper tools to evaluate the condition of the belts,” Hogg says.

And let’s not overlook what are perhaps the three most important bits: thermostats, radiator caps, and the humble hose clamp.

The cap, Hogg says, is designed to maintain a certain pressure in the engine.

DEF tanks are designed to accommodate the expansion of frozen diesel exhaust fluid. Contents are heated by coolant loops. 
DEF tanks are designed to accommodate the expansion of frozen diesel exhaust fluid. Contents are heated by coolant loops.

“Coolant will boil at a higher temperature when it’s under pressure. If the cap allows the pressure to drop, the engine will overheat, just like when you operate the engine at higher altitudes. If the cap isn’t doing its job, the system could display all sorts of systems that might lead one to think it’s a more expensive problem.”

Hogg says leaks are most likely to appear when temperatures plunge because the metal of the engine, including the fittings coolant hoses are attached to. When the metal contracts, the clamps aren’t as tight and they could start leaking.

He suggests checking the torque on the clamps, being careful not to over tighten them when it’s really cold. The engine metal will expand again when it gets hot, and if the clamp is too tight, the expanding metal fitting could snap the clamp.

While cooling system maintenance is anything but discretionary, its importance may not be fully appreciated.

“The engine makers tell me that about 40% of the major engine failures today are related to coolant,” says Hogg. “Particularly poor cooling system maintenance.”

Comments

  1. 1. kuldeep singh [ July 28, 2016 @ 01:32AM ]

    what are you writing man? If you are sharing some sort of information than share complete information. the degrees of temperature you have mentioned are in Celsius or Fahrenheit?

 

Comment On This Story

Name:  
Email:  
Comment: (Maximum 2000 characters)  
Leave this field empty:
* Please note that every comment is moderated.

Newsletter

We offer e-newsletters that deliver targeted news and information for the entire fleet industry.

GotQuestions?
sponsored by
sponsor logo

ELDs and Telematics

Scott Sutarik from Geotab will answer your questions and challenges

View All
GotQuestions?

Sleeper Cab Power

Steve Carlson from Xantrex will answer your questions and challenges

View All