5 Must-Have Tools for Your Tire Shop

When it comes to tire installation, there's no room for make-dos or this-will-do-in-a-pinch tools.

March 2013, - WebXclusive

by Jim Park, Equipment Editor - Also by this author

SHARING TOOLS        | Print Subscribe

4) Torque Wrench

Who hasn't seen a tire guy whaling away on wheel lug nuts with a big 1-inch impact wrench? Sure, it gets the nut on tight, but how tight is anybody's guess.

Too tight and it can stretch the stud and damage the nut. Not tight enough and the nut could easily come off, along with the other nine nuts and your wheel. Nobody wants a wheel-off incident, but a surprising number of small operators court disaster everyday by not using the proper tool to install truck wheels, namely, a calibrated torque wrench.

The Technology & Maintenance Council of the American Trucking Associations, the Tire and Rim Association, and several other groups have specific torque requirements for wheel fastening hardware. You can't even get into the ballpark with a conventional impact wrench. Impact wrenches are fine for running the nuts onto the studs and getting the wheel centered on the hub pilots, but that's as far as their usefulness goes. The final couple of turns on the nut should be made with a calibrated torque wrench. 

5) The Instructions

Many males have this thing about instructions. Here, a good case can be made for making sure your tire technician -- who in some really small fleets may also be the dispatcher and recruiter -- has been trained and certified in truck tire and wheel installation. In fact, it's required under regulation. As a fleet owner, you'll be under the microscope if the company is involved in a wheel-related failure, so training certificates and proper policy and procedures manuals are vital.

These are available from TMC, OSHA, the Rubber Manufacturers Association and other organizations as well as private sector suppliers such as J.J. Keller & Associates.

Because it's relatively easy to get a tire off and back onto a truck, doing it yourself can seem like an easy to save a few bucks on a professional service call. But don't kid yourself. Having the right tools is just the beginning.

Tooling a shop and certifying technicians for tire work can be an expensive undertaking. Couple that with the difficulty finding trained technicians, as well as the liability inherent with tire service, it's easier to see why many fleets opt to outsource their tire work.

Southeastern Freight Lines' tire manager, Harold Black, says his technicians do no repairs or tire breakdown work -- it's all outsourced.

"Our technicians are responsible only for airing up tires that are not flat, for conducting inspections, and removing and installing tires on vehicles," Black says. "We have a policy requiring any tire that is less than 80-percent inflated -- for us, this is 80 PSI -- to be removed from the vehicle and sent to our vendor for inspection, evaluation and possible repair."

Black says his technicians will do only the odd bead-seating job in the shop, but he still has to have all the prescribed safety equipment.

Just remember before you start, there's a reason the pros charge real money for the service. You can do it yourself, but make sure you have the right tools before you start. 

« Previous  |  1  2  |  Next »


  1. 1. Terry Cornelius [ March 30, 2014 @ 09:10AM ]

    Todd, is a very respectable gentleman in the tire industry. Lessons from him should be taken with some true hearted thought. Lesson that his current employer should consider strongly in their quest for the mighty dollar, and truly should show real concern for their employees instead of just numbers on a board. Along with the tools mentioned in the above there is also the Jack stands that prevent the unit from falling to the ground or worse yet on a technician the safety glasses that prevent foreign materials from going to an eye with the burst of air from the impact guns, Gloves that prevent cuts and abrasions to the hands and fingers ah and lets not forget the investigation process that does occur when an unfortunate incident does happen. Like what did the tech do wrong to cause him or her to get hurt in the first place. Just to add a few more thoughts to the correct tools for the work place How many good people have lost jobs to an unfortunate incident???

    Terry Cornelius


Comment On This Story

Comment: (Maximum 2000 characters)  
Leave this field empty:
* Please note that every comment is moderated.


We offer e-newsletters that deliver targeted news and information for the entire fleet industry.


ELDs and Telematics

sponsored by
sponsor logo

Scott Sutarik from Geotab will answer your questions and challenges

View All

Sleeper Cab Power

Steve Carlson from Xantrex will answer your questions and challenges

View All