Maintenance

Keeping An Eye on 
Axles and Suspensions

May 2012, TruckingInfo.com - Feature

by Jim Park, Equipment Editor, Equipment Editor - Also by this author

SHARING TOOLS        | Print Subscribe
Although the maintenance-free tractor-trailer is still a few years off, there are really only two big maintenance items left when it comes to axles and suspensions: the shock absorbers and the air springs. Some historically large maintenance items today are designed to almost outlive the trucks.
Shocks are a small components with big 
performance implications. Look for oil residue on the shock tube, and check for bushing wear.
Shocks are a small components with big 
performance implications. Look for oil residue on the shock tube, and check for bushing wear.
Parts such as main pivot bushings on a trailing arm suspension now come with 5- to 7-year warranties.

"The technology is now so good, you don't really have to concern yourself with those things on an annual basis," says Mike Edlund, a suspension application engineer at SAF-Holland. "Back in the old days, everything would wear and seat, and that meant steady work for the guys in the shop. It's not like that anymore - but that doesn't mean you can just ignore stuff below the frame rails."

Drive axles

ADVERTISEMENT

While the axle housings themselves require little maintenance other than visual inspection for cracked or broken welds or loose mounting hardware, the seals and axle lubricant need a little attention periodically.

"At the engine oil change interval, it is customary to check the lubricant level in the axle to ensure it is still filled to the appropriate level," says Steve Slesinski, director of global product planning for commercial vehicle products at Dana Holding Corp. Other points that should be inspected, he says, are the carrier-to-housing connection, wheel seals, the pinion input or output shields (check for oil buildup or dirt), and the housing breather (check to see if it's missing or damaged).

A damaged breather could allow contaminants to enter the axle, compromising the lubricant. Conversely, if the breather is plugged, heat in the axle could cause pressure inside the housing to force lubricant out through the wheel or pinion seals, leading to an incorrect diagnosis of a seal failure.

The breather allows a little vapor to escape from the axle, and the area around the breather may appear wet or caked with dirt. According to Charlie Allen, general manager for rear drive axles at Meritor, a little wetness around the air vent on the axle is normal.

"Excessive wetness is not normal. Our new breather has a built-in oil separator to address oil getting out," he says. "Another source of oil around the breather is the fit of the breather in the axle housing. Using a thread sealant will put a stop to seepage."

It's also important to look after the axle lubricant. Many axle warranties now go out to 750,000 miles, but proper lubrication is required.

According to Bruce McGlone, senior chemist, materials engineering at Meritor, only correct and hardware-approved multi-viscosity oils should be used in axles and wheel ends.

"Approved oils will exhibit a longer in-use life and be more capable of addressing road concerns such as heat, contamination, loads/grades and driver dynamics," he says.

The other obvious maintenance implication for drive axles is alignment. Misaligned axles can wreak havoc with tires, especially steer tires, resulting in a misdiagnosis of the problem.

A quick-and-dirty method of ensuring the drive axles are reasonably well-aligned is to measure them in relation to the frame and each other. With the wheels chocked and the brake released, measure the distance between the axles. It should be the same on both sides. Also measure the distance from a fixed point on the axle, such as the brake spider, to the frame rail. Again, the measurements should be the same. If there is variance, consider a full-chassis alignment job.

Steer axles

Although drive axles only require visual inspection prior to their 500,000-mile initial service interval, steer axles demand a closer look about every 25,000 miles, depending on the application. Kingpins, tie rods and various ball joints are all in constant motion and in need of lubrication.

"When lubricating, it is critical to add lubrication until you see fresh grease start to purge from the product to ensure all contaminants have been flushed out of the system," Slesinksi says. "It is also critical to make every effort to keep contaminants out of the product whenever possible to extend steer axle life."

Some suspensions still require lube in the spring hangers and shackles, so don't overlook those. Remember to use the proper lubricant when greasing automatic brake adjusters.

Shock absorbers are a frequent maintenance item. They can wear out over time, and the mounting bushings can wear or crack. Both will affect the performance of the shock and, ultimately, the ride and handling and probably tire wear.

To tell if a shock is working properly, grasp the lower barrel of the shock just after it has come off the road. "It should be warm to the touch," Edlund says. "That tells you the internal mechanism is working." In this case, cold is bad. "The other telltale sign of a shock failure is when the lower tube has dust and dirt clinging to the body," he says. " That means oil has seeped out, and dust is clinging to the oil. If you can see that, the shock should be changed."

Suspensions

Beyond visual inspections and the occasional retorqeuing, steel spring suspensions are pretty much maintenance-free. Being made of metal, though, means corrosion and stress cracks will be factors.

"Inspect each frame hanger and replace any that have developed cracks or are badly rusted," Hendrickson recommends. "High-mileage springs with one or more leaves broken below the number two leaf should be replaced with a new spring assembly of the same part number. Replacing both springs will assure even spring deflection."

According to Reyco Granning, you can check leaves for cracks by examing the side of the spring packs. Rivulets of rust may appear on the side of the pack near a crack that can't be seen.
In air suspensions, the alignment of the air spring, the air spring itself and the pivot bushings all need periodic inspection.

According to Dave Vanette, manager of new business development at Firestone Industrial Products, most premature air spring failures are caused by other problems with the suspension system.

"Air lines may break loose and rub against air springs, causing abrasions or tears in the rubber bellows. Bushings may wear out and cause similar damage due to misalignment of the air spring," he says. "The most common problem found in non-warranty air spring product returns is overextension of the air spring, typically caused by a broken shock absorber. When a shock absorber breaks, it allows the air spring to travel too far and essentially tears the air spring apart."

Proper air spring inspection involves scanning the air spring for any signs of irregular wear or heat cracking. "The annual inspection should include checks for buildup of dirt, debris or corrosion on the piston (pedestal), which can create a surface similar to sandpaper and wear down the air spring," he notes. "If anything is found to be rubbing against the air springs, the driver should take the rig in for service."

The other essential component in an air suspension system, the leveling valve, should be checked for proper operation.

"It's essential for maintaining proper ride height as set by the vehicle manufacturer," says Randy Petresh, vice president of technical services at Haldex. "Ride height isn't a user-selected parameter based on preference. It's there to maintain proper driveline angles and maintain the correct height of the trailer."

Because they are pneumatically operated mechanical leveling valves, they are subject to air contamination, corrosion and possible physical damage. Cycle the valve through its extremes and make sure the moving parts are not binding.

Check th

Comment On This Story

Name:  
Email:  
Comment: (Maximum 2000 characters)  
Leave this field empty:
* Please note that every comment is moderated.

Newsletter

We offer e-newsletters that deliver targeted news and information for the entire fleet industry.



GotQuestions?

LUBRICANTS

The expert, Mark Betner from Citgo will answer your questions
Ask a question

Sponsored by

Magazine