Equipment

TMC

1  -  6  of  6

May 2014, TruckingInfo.com - Department

Trailer Maintenance Tips

It’s difficult to find a damaged rear impact guard because owners and drivers know they must be fixed before going on the road. Surface rust and dirt shouldn’t result in a citation, but deeper corrosion and bends might. Every trailer builder’s guard is different, so parts from individual manufacturers must be used in repairs.

By Tom Berg and Jim Park

It’s been 14 years since repairing any trailer’s “ICC bumper” was a simple matter of cutting off the damaged section and welding on a straight piece of angle iron. Most trailers built since Jan. 26, 1998, have been equipped with more complex required rear impact guards that are not only stronger but are designed to absorb shock from a collision.

Tags: Trailers, TMC, Fifth Wheels, Stoughton Trailers, ICC Bumpers, Rear Impact Guards

April 2014, TruckingInfo.com - Department

Tending Liftgate Batteries

By Tom Berg

Bruce Purkey knows where the electrons go. And, as president of Purkey’s Fleet Electric and his many activities in the Technology & Maintenance Council of the American Trucking Associations, he’s well aware that some of them flow to batteries that support the electric-over-hydraulic systems for liftgates on trucks and trailers. Usually there are two and as many as four Group 31 batteries, like the ones on a truck or tractor.

Tags: Trailers, TMC, Waltco, Maxon, Idle Reduction, Batteries, Con-Way, Purkey's Fleet Electric, Trail Charger, Sure Power Industries

April 2014, TruckingInfo.com - Department

Ounces of Prevention Means Miles of Cure For Your Tires

Alignment and balancing can keep your tires and your truck running straight and true.

By Jim Park

Unlike their human counterparts, dead tires do tell tales. And aside from underinflation and road strikes, the tales most commonly told of tires robbing their owners of full value revolve around alignment. Scrubbing and scuffing and driving tires off in different directions, poor alignment kills tires faster than almost any other mechanical malady.

Tags: TMC, Tires, Alignment, Bee Line Company, Hunter Engineering, IMI, Tires and Wheels, E-Z Line, Counteract Balancing Beads

March 2014, TruckingInfo.com - WebXclusive

The Lowdown on the New Low-Viscosity Oils

Kinematic viscosity is what you might envision when thinking of viscosity – gravitational flow. But the new oils will meet viscosity standards measured at high temperatures/high shear conditions.

By Deborah Lockridge

Exactly what is this "high-temp, high-shear" viscosity engine oil standard in the works for the next round of EPA emissions standards, and what are engine makers doing to make sure engines will still be well protected?

Tags: Fuel and Oil, Engines, Fuel Economy, GHG emissions, Engine Oil, TMC, API

January 2014, TruckingInfo.com - Department

Keeping Your Wheels in the Game (updated)

Pictures are worth a thousand words, they say. What sort of a message do the wheels on this trailer convey about its owner?

By Jim Park

Back in 1984, the Occupational Safety and Health Administration issued a regulation requiring that truck wheels be stripped of rust and debris before mounting a tire. Easier said than done, the industry moaned at the time. Labor was less costly then, but wire brushes and elbow grease weren’t going to cut it.

Tags: OSHA, Goodyear, CSA, TMC, Tires, Wheels, IMI, Wheel refinishing, Maxion Wheel

January 2014, TruckingInfo.com - Feature

Will Truck Owners Face GHG Enforcement?

By Tom Berg and Oliver Patton

Truck owners and manufacturers share responsibility for compliance with new limits on carbon dioxide emissions and fuel economy.

Tags: ATA, GHG, TMC, EPA, Clean Air Act, GHG emissions, NHTSA

« Previous1Next »

Newsletter

We offer e-newsletters that deliver targeted news and information for the entire fleet industry.



GotQuestions?

LUBRICANTS

The expert, Mark Betner from Citgo will answer your questions
Ask a question

Sponsored by

Magazine