Drivers

Making the Case for Fuel-Efficient Tires

Low-rolling-resistance tires and wide-base singles have their place and their purpose, but proving it can be a challenge.

June 2013, TruckingInfo.com - Feature

by Jim Park, Equipment Editor - Also by this author

SHARING TOOLS        | Print Subscribe
The more rubber you have on the road, the sooner the improvements become obvious.
The more rubber you have on the road, the sooner the improvements become obvious.

You get 30% less tread on some fuel-efficient tires, they cost 15% less up front and they run fewer miles to take-off, but does the money saved on fuel because of the lower rolling resistance make up for the shorter overall life?

Many fleets are struggling with that question today. The answer is often anything but clear.

But don't be too quick to blame the tires.

ADVERTISEMENT

Mike Jeffress, vice president of maintenance at Arkansas-based Maverick Transportation, is one such fleet. Asked if he has ever done cost/benefit calculations on shallow-tread, fuel-efficient tires, he chuckled and said, "fuel economy is a very convoluted scenario.”

"When you get everything in the fleet set up the way you want it and you can measure fuel economy across the fleet, and you find you're getting 7 mpg at 62 mph, it's good," he says. "Then a few things change, more aero equipment comes in, new drivers come in and old ones leave, speed limits change, but the fuel economy remains 7 mpg. I can't put it all down to the tires but I'm inclined to believe the tire makers' claims are true."

Maverick did some extensive Type IV fuel economy testing 10 years ago with the Michelin X One wide-base singles tires came on to the market. Jeffress says he saw 2/10 of a mile per gallon improvement using the wide-single tires on drive axles only.

"But on tire life, where we used to get 260,000 miles to removal from a set of duals, we dropped to 210,000 miles with the singles," he notes. Nevertheless, "even though we were short on miles to wear-out, our test results showed the wide singles made sense."

Fuel-efficient tires come in many shapes and sizes. Traction, tread depth, miles-per-32nd and rolling resistance are the variables you must contend with. Hard, reliable comparisons won't be easy to come by.
Fuel-efficient tires come in many shapes and sizes. Traction, tread depth, miles-per-32nd and rolling resistance are the variables you must contend with. Hard, reliable comparisons won't be easy to come by.

Sometimes other advantages that might not appear on the fuel reports can add to the attractiveness of the tires.

Roy Gambrell, director of maintenance for Truck It, Cottontown, Tenn., and formerly general chairman of the ATA's Technology and Maintenance Council, runs fuel-efficient shallow-tread duals on his trailer. He found with less rubber on the tires to begin with, they were less susceptible to dipping and cupping wear common to free-rolling positions.

"The problem with that kind of wear, once it starts, it's impossible to stop," Gambrell told HDT. "But if it never starts, the tires actually last longer than standard tires used to on a trailer, even though there are fewer 32nds of rubber there to begin with.

"As for fuel economy gains, I really can't say. We move so many different things from one day to the next, it's hard to get the consistency you need for an accurate fuel test."

The secret sauce

Gambrell's observations about miles to removal are likely the result of compounding and tread design improvements. Until recently, you spec'd for traction, tread life, or low rolling resistance. Often, you gave up one to get more of the other two. It was difficult to get all three in equal measure.

William Estupinan, GITI Tire vice president of technical service for the Americas, says when major tire manufacturers began using silica in commercial tire treads, miles to removal improved. Since then, traction and rolling resistance have improved as well.

"In the beginning, there were certainly compromises to be made," he says. "That's hardly the case anymore. You can achieve a good balance between traction, tire life and rolling resistance."

Further, today's casings are optimized to lower rolling resistance by refining stress distribution and minimizing internal friction caused when the sidewall flexes under load. In the case of wide-base single tires, two sidewalls per wheel position are eliminated, further reducing the tires’ overall rolling resistance.

The remaining percentage of a tire's rolling resistance comes from the tire tread. That's why much of the focus in developing fuel-efficient tires has been on tread design.

"Some compounds, especially those incorporating silica, or using formulas that combine natural and engineered synthetic rubber, can reduce tire rolling resistance significantly," says Guy Walenga, director of engineering for commercial products and technologies at Bridgestone.

Proving the case

Fleet uptake of the newer fuel-efficient tires has been good, notes Curtis Decker, manager of product development, Continental Tire North America, but he believes many fleets are missing out on savings because they have a harder time proving them.

"Tire makers have the burden of proving to the customer that the technology works, but there's only so much we can hand them," he says. "People are naturally skeptical about marketing claims. And it's harder for some fleets to evaluate the efficiency of the tires – especially smaller fleets – because of the need for direct side-by-side comparisons."

The problem with tire comparisons is there are so many variables that must be isolated or eliminated, lest they taint the results.  

"Fleets have to clean up their tire maintenance house before embarking on an evaluation," Decker says. "If factors like alignment and tire pressure management – especially pressure management – aren't perfect going in, the results will be skewed."

So if you can't test them yourself, and you're not sure about the marketing hype, how do you know the tires are working for you?

Don't feel bad. Even a fleet as sophisticated Maverick can't always nail everything down to two decimal points.

"I think a lot of fleets are struggling with the miles-to-removal question, especially if the improvement in the fuel numbers is lost in the noise," Jeffress says. "It's not going to be a big number."

Until recently, you spec'd for traction, tread life or low rolling resistance. Often, you gave up one to get more of the other two.
Until recently, you spec'd for traction, tread life or low rolling resistance. Often, you gave up one to get more of the other two.

Jeffress is responsible for fuel economy at Maverick, though his department doesn't pay the fuel bills. But if fuel mileage began dropping, he'd sure hear about it.

"If I was just one guy tasked with managing fuel economy and maintenance costs, I would be watching to see if fuel costs were climbing, dropping or staying the same and whether my miles per 32nd were changing," he says. "It's way too easy to get tricked with a couple of trucks and a couple of sets of tires. It's a 'big picture' exercise."

Fuel economy in the city

The recognized benefits of fuel-efficient tires in a long-haul environment are fairly obvious, but not so much in urban situations. Curb strikes and scrubbing from tight turns are big threats to tire longevity, and annual miles pale in comparison to over-the-road trucks. On the highway, because of the high number of miles, even a 0.3% improvement is noticeable.

Still, fuel-efficient tires are making their way into medium-duty markets, driven in no small part by new federal fuel efficiency requirements. Not much can be done to improve aerodynamics on trucks that don't often go over 30 mph, so the potential for improvement lies elsewhere.

"The new fuel economy regulations are certainly rearranging the priorities for tire manufacturers," says Brad Weaver, product portfolio manager at Michelin. "Things like aerodynamics don't even apply in the medium-duty market. The original equipment manufacturer's improvement options are very limited – smaller engines and lower rolling resistance tires.

"As tire makers, we have to begin putting a higher priority on fuel economy and offering products that will help the original equipment manufacturers meet their targets."

The urban nature of the segment does bring a few challenges.

Shallower tread depth on low-rolling-resistance tires can be seen as a threat to urban and vocational trucks, where a thick layer of protection between the road and the casing is seen as beneficial. However, ongoing product development programs are focused on producing a tire for an urban setting with lower rolling resistance and the same damage-mitigating performance attributes as before.

"We'll be taking essentially the same approach we did with the on-highway market, using tread compounds and designs to reduce rolling resistance while maintaining traction and durability," Weaver says. "But it won't be the same tire at all. In the medium duty and vocational market, the priorities are different. It's a more abusive environment with concerns about curbing, scrubbing, etc."

Goodyear's Don Kramer, director of marketing commercial tires, says customers won't have to accept "less of a tire" because of thinner, more efficient tread. He says manufacturers have improved manufacturing processes and made big gains in materials.

"In the past, we had two choices in tread compounding – tread wear or fuel efficiency – and the fleet had to choose. Sometimes there were huge trade-offs," he says. "That's not so today. Some steer and drive tires could have as many as two to four different compounds in the tread area to minimize those trade-offs. It will be the same for medium-duty tires as well."

 

Comments

  1. 1. J.M. MacKellar [ June 11, 2013 @ 07:15AM ]

    I will go with what Mike had to say, there are a great many variables that enter into the equation I think the biggest one is the driver. I started running wide base tires when they first came out. We were running two and three axle tractors pulling bottom dumps or side dumps the tractors had all the same engines and all were geared for 58 miles an hour, we were running two shifts a day pulling out of the Los Angeles area over the Grapevine into the Central Valley. We noted on scales both ways so we were always at the maximum legal load limit. This is California. Over a period of three years there was about a 4% difference between widebase and duels. The big difference was in the driver, you put different drivers in the same tractor pulling the same load the mileage is that the different. The one thing not mentioned in your article was the weight saving factor. For us this was a big item. Having been a member of TMC for over 30 years I have known both Mike and Roy and believe they run excellent maintenance programs.

    You forgot to mention that Mike was also chairman of TMC.

  2. 2. Austin. Libby [ June 24, 2013 @ 04:21PM ]

    One Night 99.9% nitrogen in your tires will give you longer wear and guaranteed ,and Professional driver Watch his foot on the gas pedal...and Mileage will improve,it's Again up to your driver( let him or her pay for the Fuelout of there Their wallet or purse then maybe they will watch there FOOT!!!!!

 

Comment On This Story

Name:  
Email:  
Comment: (Maximum 2000 characters)  
Leave this field empty:
* Please note that every comment is moderated.

Newsletter

We offer e-newsletters that deliver targeted news and information for the entire fleet industry.



GotQuestions?

LUBRICANTS

The expert, Mark Betner from Citgo will answer your questions
Ask a question

Sponsored by

Magazine