Article

Trailer Report: Weight vs. Cost

October 2011, TruckingInfo.com - Feature

by Tom Berg, Senior Editor, Senior Editor - Also by this author

SHARING TOOLS        | Print Subscribe
How important is saving weight? It's vital in some operations, such as hauling bulk commodities, especially if trailers are always loaded to the max and tare weight must be cut to enhance payload potential.
Plastic sheeting and aluminum extrusions and fabrications combine to cut many pounds from this trash-transfer trailer shown at the 2011 Mid-America Trucking Show.
Plastic sheeting and aluminum extrusions and fabrications combine to cut many pounds from this trash-transfer trailer shown at the 2011 Mid-America Trucking Show.
Some fleet managers have calculated that a pound saved adds X number of dollars of revenue over the life of a trailer. For bigger fleets, "X" can run into the thousands.

In other operations, such as dry and refrigerated freight, saving weight is less important. Cargoes weigh varying amounts, and rates for certain dense commodities might not support the cost to buy lightweight trailers to carry them in the quantities that some shippers want.

An indirect example is the 53-foot trailer. It became the predominant length for vans and reefers by the end of the 1990s, when 53s replaced 48-footers in most fleets. A 53-footer weighs several hundred pounds more and costs thousands more to buy. But while shippers demand 53s, their full volume is seldom used.

That's the case in reefers, anyway, said Corey England, chief operating officer of C.R. England Inc. and a former chairman of the Truckload Carriers Association Refrigerated Division.

"The red line is back there on the floor, marking off the last 3 feet, but it's almost never filled," England commented in a conversation during a break at the group's annual meeting last year. "But customers want it."

Many shippers give loading responsibilities completely to forklift operators, and some of them want the flexibility of that long floor. They'll occasionally use all of it to spread out weight instead of figuring a correct way of stacking merchandise in a shorter length.

"We've thought of asking Utility or someone to build us 50-foot trailers, because they'd almost always be long enough," England said. "California requires the extra [SmartWay-type] equipment on 53s, so we could avoid that if we ran 50s. Of course, if enough of us did that, they'd catch on pretty quick and change the rules" to include 50-foot trailers.

"But we couldn't do that anyway because customers want 53s. If you can't display that '53' label on it, they turn you away."

Long vs. lightweight

Some types of dry "balloon" freight can completely fill a 53, so for-hire carriers use 53s to stay flexible. Private fleets use what's best for their products - unless they backhaul general freight. That can force them to operate equipment just like their for-hire brothers and sisters.

A long trailer is one thing. A long and especially light­weight one is another, or should be.

Schneider National looks carefully at payload versus rates and specs out trailers accordingly. But, "We've never come to a definite conclusion" about payback, said Steve Duley, vice president, purchasing. "We've had a weight that's acceptable to most accounts. If you've got 50 pounds to go, you look at what the freight will pay and how much money we can make on it. Then we might pay a lot for that last 50 pounds."

A Schneider van may look stout, but it's been carefully thought out, and some lightweight components are there, especially for dedicated hauls. "It may not be obvious, but given the work we do, we do look at weight," Duley said. "But we balance that against the life of the truck, the needs of the driver, and what they'll be doing."

Included are composite side walls. In Wabash National vans, Schneider buys the DuraPlate wall, which has steel skin over a plastic honeycomb. They buy a comparable wall from Hyundai. The Wabash wall has a 2-foot-high base rail, called the Heavy Duty rail. This is an aluminum extrusion to withstand forklift damage.

Schneider also specs a Havco wood-plastic composite flooring, which saves 50 pounds compared to a hardwood floor on a 53-footer.

"You can get more weight out by going with a thinner floor, but we upgraded the rating" while still saving some weight, Duley said. Going from four lock rods on the rear swing doors to three saves another 20 to 30 pounds. Four rods tightly lock the doors and stiffen the body, adding life, but three work almost as well.

Some of Schneider's dedicated accounts get wide-base single wheels and tires on the trailers that serve them. But wheels are steel instead of aluminum to make them less attractive to thieves. The big single tires alone save about 200 pounds per tandem over dual, standard-size tires and steel wheels. All vans ride on Hutch EZ-Pull steel-spring suspensions, which are lighter and cost less than air-ride. Trailers that go on rail cars have lift pads and other equipment, but some items are being removed and lighter-weight pads installed to save about 50 pounds.

More payload's not the only reason to spec weight-saving components. Schneider's weight-cutting efforts took about 200 pounds off each trailer, which allowed it to add Ridge Green Wing side skirts without adding weight. It's equipping all of its 30,000 vans with side skirts to comply with California's fuel and greenhouse-gas regulations.

Corrosion & strength

While not a weight item, corrosion resistance has become important, so Schneider specs galvanized steel door headers, rear subframe, and landing gear. "We believe it will help, especially in the lower corners of the header, where moisture tends to gather, and in the subframe," he said.

"We don't try to lighten the underside," Duley said, because strength there is important to long life. Schneider aims to operate its vans at least 10 years, "then we inspect them and do some maintenance, and pull by condition" for as long as it's safely and economically feasible.

Schneider pays $25,000 to $30,000 for a van, depending on details. Each weighs 14,200 to 14,300 pounds, and can carry a payload of 47,500 pounds with an older tractor or 46,500 with a new tractor. With a 72-inch sleeper, an older tractor weighs 18,200 pounds, which is 1,000 less than a new tractor that has a heavier 2010-spec diesel with selective catalytic reduction emissions aftertreatment equipment.

The company considered a smaller sleeper, but they still have a thousand driver teams that need the large sleeper-cab. "They usually get new trucks, run them a year, then the trucks go into single driver use. We have bought some smaller sleepers, about a foot to 18 inches shorter. With reduced wheelbase and everything else that follows, they save 300 to 400 pounds" versus a 72-incher.

Tankers run by Schneider's bulk division get similar attention to weight-saving details balanced against other considerations. Among them is the fact that shippers often send loads that are less than a full truckload because that's what their customers specify. Some get the wide-base tires on steel wheels, which save about 200 pounds over standard duals. The fleet likes wide brakes for long lining life, but uses smaller brakes on certain accounts.

Otherwise the tankers are spec'd for durability and long service life. The cost is $50,000 to $75,000 for a standard chemical tank. Schneider wants them to last infinitely, and there is no trade cycle. "We do a lot of maintenance on them and inspect them often," Duley said. At 15 to 20 years they are put on limited runs.

Aluminum, yes, but...

To save weight in a trailer (or a tractor, for that matter), look at aluminum in everything. But it always costs more than steel. And while some aluminum components fight corrosion and last longer, others suffer fatigue and give less life. Some cost less than others on a per-pound-saved basis. For instance, cast or fabricated aluminum brackets and wheel hubs cost less than forged aluminum wheels.

Each builder has features designed to cut weight and add volume, like thin walls, where aluminum sheet-and-post is still a popular construction. Here aluminum posts can be spec'd instead of the usual steel. Newer composite walls, often employing a foam core with sheet metal skins, are also lightweight

Comment On This Story

Name:  
Email:  
Comment: (Maximum 2000 characters)  
Leave this field empty:
* Please note that every comment is moderated.

Newsletter

We offer e-newsletters that deliver targeted news and information for the entire fleet industry.



GotQuestions?

LUBRICANTS

The expert, Mark Betner from Citgo will answer your questions
Ask a question

Sponsored by

Magazine